AIX Error Code
AIX Error Code입니다.
Diagnostic Load Progress Indicators Top of page
c00 AIX Install/Maintenance loaded successfully.
c01 Insert the first diagnostic diskette.
c02 Diskettes inserted out of sequence.
c03 The wrong diskette is in diskette drive.
c04 The loading stopped with an irrecoverable error.
c05 A diskette error occurred.
c06 The rc.boot configuration shell script is unable to determine type of boot.
c07 Insert the next diagnostic diskette.
c08 RAM file system started incorrectly.
c09 The diskette drive is reading or writing a diskette.
c20 An unexpected halt occurred, and the system is configured to enter the kernel debug program instead of entering a ystem dump.
c21 The ifconfig command was unable to configure the network for the client network host.
c22 The tftp command was unable to read client's ClientHostName info file during a client network boot.
c24 Unable to read client's ClientHostName.info file during a client network boot.
c25 Client did not mount remote miniroot during network install.
c26 Client did not mount the /usr file system during the network boot.
c29 The system was unable to configure the network device.
c31 Select the console display for the diagnostics. To select No console display, set the key mode switch to Normal then to Service.
c01 Insert the first diagnostic diskette.
c02 Diskettes inserted out of sequence.
c03 The wrong diskette is in diskette drive.
c04 The loading stopped with an irrecoverable error.
c05 A diskette error occurred.
c06 The rc.boot configuration shell script is unable to determine type of boot.
c07 Insert the next diagnostic diskette.
c08 RAM file system started incorrectly.
c09 The diskette drive is reading or writing a diskette.
c20 An unexpected halt occurred, and the system is configured to enter the kernel debug program instead of entering a ystem dump.
c21 The ifconfig command was unable to configure the network for the client network host.
c22 The tftp command was unable to read client's ClientHostName info file during a client network boot.
c24 Unable to read client's ClientHostName.info file during a client network boot.
c25 Client did not mount remote miniroot during network install.
c26 Client did not mount the /usr file system during the network boot.
c29 The system was unable to configure the network device.
c31 Select the console display for the diagnostics. To select No console display, set the key mode switch to Normal then to Service.
The diagnostic programs then load and run the diagnostics automatically. If you continue to get the message, check the cables and make sure you are using the serial port.
c32 A directly attached display (HFT) was selected.
c33 A TTY terminal attached to serial ports S1 or S2 was selected.
c34 A file was selected. The console messages store in a file.
c35 No console found.
c40 Configuration files are being restored.
c41 Could not determine the boot type or device.
c42 Extracting data files from diskette.
c43 Cannot access the boot/install tape.
c44 Initializing installation database with target disk information.
c45 Cannot configure the console.
c46 Normal installation processing.
c47 Could not create a physical volume identifier (PVID) on disk.
c48 Prompting you for input.
c49 Could not create or form the JFS log.
c50 Creating root volume group on target disks.
c51 No paging devices were found.
c52 Changing from RAM environment to disk environment.
c53 Not enough space in the /tmp directory to do a preservation installation.
c54 Installing either BOS or additional packages.
c55 Could not remove the specified logical volume in a preservation installation.
c56 Running user-defined customization.
c57 Failure to restore BOS.
c58 Displaying message to turn the key.
c59 Could not copy either device special files, device ODM, or volume group information from RAM to disk.
c61 Failed to create the boot image.
c62 Loading platform dependent debug files.
c63 Loading platform dependent data files.
c64 Failed to load platform dependent data files.
c70 Problem Mounting diagnostic CD-ROM disc.
c99 Diagnostics have completed. This code is only used when there is no console.
Fxx (xx is any number) Refer to Firmware chapter of the service manual.
c32 A directly attached display (HFT) was selected.
c33 A TTY terminal attached to serial ports S1 or S2 was selected.
c34 A file was selected. The console messages store in a file.
c35 No console found.
c40 Configuration files are being restored.
c41 Could not determine the boot type or device.
c42 Extracting data files from diskette.
c43 Cannot access the boot/install tape.
c44 Initializing installation database with target disk information.
c45 Cannot configure the console.
c46 Normal installation processing.
c47 Could not create a physical volume identifier (PVID) on disk.
c48 Prompting you for input.
c49 Could not create or form the JFS log.
c50 Creating root volume group on target disks.
c51 No paging devices were found.
c52 Changing from RAM environment to disk environment.
c53 Not enough space in the /tmp directory to do a preservation installation.
c54 Installing either BOS or additional packages.
c55 Could not remove the specified logical volume in a preservation installation.
c56 Running user-defined customization.
c57 Failure to restore BOS.
c58 Displaying message to turn the key.
c59 Could not copy either device special files, device ODM, or volume group information from RAM to disk.
c61 Failed to create the boot image.
c62 Loading platform dependent debug files.
c63 Loading platform dependent data files.
c64 Failed to load platform dependent data files.
c70 Problem Mounting diagnostic CD-ROM disc.
c99 Diagnostics have completed. This code is only used when there is no console.
Fxx (xx is any number) Refer to Firmware chapter of the service manual.
Dump Progress Indicators (Dump Status Codes) 0c0 The dump completed successfully.
0c1 The dump failed due to an I/O error.
0c2 A dump, requested by the user, is started.
0c3 The dump is inhibited.
0c4 The dump device is not large enough.
0c5 The dump did not start, or the dump crashed.
0c6 Dumping to a secondary dump device.
0c7 Reserved.
0c8 The dump function is disabled.
0c9 A dump is in progress.
0cc Unknown dump failure
Crash Codes
Category 1
Dump analysis is the appropriate first action in Problem Determination, begin the Problem Determination process with software support.
Category 2
Dump analysis most likely will not aid in Problem Determination, begin the Problem Determination process with hardware support.
Category 3
Both software and hardware support may be needed in Problem Determination, go to MAP 0070:
Dump analysis is the appropriate first action in Problem Determination, begin the Problem Determination process with software support.
Category 2
Dump analysis most likely will not aid in Problem Determination, begin the Problem Determination process with hardware support.
Category 3
Both software and hardware support may be needed in Problem Determination, go to MAP 0070:
888 Sequence in Operator Panel Display in Diagnostic Information for Multiple Bus Systemsto assist in problem isolation.
Category 1
300 Data storage interrupt from the processor.
32x Data storage interrupt because of an I/O exception from IOCC.
38x Data storage interrupt because of an I/O exception from SLA.
400 Instruction storage interrupt.
700 Program interrupt.
Category 2
200 Machine check because of a memory bus error.
201 Machine check because of a memory timeout.
202 Machine check because of a memory card failure.
203 Machine check because of a out of range address.
204 Machine check because of an attempt to write to ROS.
205 Machine check because of an uncorrectable address parity.
206 Machine check because of an uncorrectable ECC error.
207 Machine check because of an unidentified error.
208 Machine check due to an L2 uncorrectable ECC.
500 External interrupt because of a scrub memory bus error.
501 External interrupt because of an unidentified error.
51x External interrupt because of a DMA memory bus error.
52x External interrupt because of an IOCC channel check.
53x External interrupt from an IOCC bus timeout; x represents the IOCC number.
54x External interrupt because of an IOCC keyboard check.
800 Floating point is not available.
300 Data storage interrupt from the processor.
32x Data storage interrupt because of an I/O exception from IOCC.
38x Data storage interrupt because of an I/O exception from SLA.
400 Instruction storage interrupt.
700 Program interrupt.
Category 2
200 Machine check because of a memory bus error.
201 Machine check because of a memory timeout.
202 Machine check because of a memory card failure.
203 Machine check because of a out of range address.
204 Machine check because of an attempt to write to ROS.
205 Machine check because of an uncorrectable address parity.
206 Machine check because of an uncorrectable ECC error.
207 Machine check because of an unidentified error.
208 Machine check due to an L2 uncorrectable ECC.
500 External interrupt because of a scrub memory bus error.
501 External interrupt because of an unidentified error.
51x External interrupt because of a DMA memory bus error.
52x External interrupt because of an IOCC channel check.
53x External interrupt from an IOCC bus timeout; x represents the IOCC number.
54x External interrupt because of an IOCC keyboard check.
800 Floating point is not available.
Category 3
000 Unexpected system interrupt.
558 There is not enough memory to continue the IPL.
600 AIX 4.3.3.3 and above: Alignment Interrupt.
If pre-AIX 4.3.3.3: AIX has crashed because the Portability Assist Layer (PAL) for this
machine type has detected a problem.
605 AIX has crashed because the Portability Assist Layer (PAL) for this
machine type has detected a problem (AIX 4.3.3.3 and above).
000 Unexpected system interrupt.
558 There is not enough memory to continue the IPL.
600 AIX 4.3.3.3 and above: Alignment Interrupt.
If pre-AIX 4.3.3.3: AIX has crashed because the Portability Assist Layer (PAL) for this
machine type has detected a problem.
605 AIX has crashed because the Portability Assist Layer (PAL) for this
machine type has detected a problem (AIX 4.3.3.3 and above).
Configuration Program Indicators 2E6 The PCI Differential Ultra SCSI adapter or the Universal PCI Differential Ultra SCSI adapter being configured.
2E7 Configuration method unable to determine if the SCSI adapter type is SE or DE type.
440 9.1GB Ultra SCSI Disk Drive being identified or configured.
441 18.2GB Ultra SCSI Disk Drive being identified or configured.
444 2-Port Multiprotocol PCI Adapter (ASIC) being identified or configured.
447 PCI 64-bit Fibre Channel Arbitrated Loop Adapter being configured.
500 Querying Standard I/O slot.
501 Querying card in Slot 1.
502 Querying card in Slot 2.
503 Querying card in Slot 3.
504 Querying card in Slot 4.
505 Querying card in Slot 5.
506 Querying card in Slot 6.
507 Querying card in Slot 7.
508 Querying card in Slot 8.
510 Starting device configuration.
511 Device configuration completed.
512 Restoring device configuration files from media.
513 Restoring basic operating system installation files from media.
516 Contacting server during network boot.
517 Mounting client remote file system during network IPL.
518 Remote mount of the root (/) and /usr file systems failed during network boot.
520 Bus configuration running.
521 /etc/init invoked cfgmgr with invalid options;
/etc/inithas been corrupted or incorrectly modified (irrecoverable error).
522 The configuration manager has been invoked with conflicting options (irrecoverable error).
523 The configuration manager is unable to access the ODM database (irrecoverable error).
524 The configuration manager is unable to access the config.rules object in the ODM database
525 The configuration manager is unable to get data from a customized device object in the ODM database
526 The configuration manager is unable to get data from a customized device driver object in the ODM database
527 The configuration manager was invoked with the phase 1 flag; running phase 1 at this point is not permitted
528 The configuration manager cannot find sequence rule, or no program name was specified in the ODM database
529 The configuration manager is unable to update ODM data (irrecoverable error).
530 The program savebase returned an error.
531 The configuration manager is unable to access the PdAt object class (irrecoverable error).
532 There is not enough memory to continue (malloc failure); irrecoverable error.
533 The configuration manager could not find a configuration method for a device.
534 The configuration manager is unable to acquire database lock (irrecoverable error).
535 HIPPI diagnostics interface driver being configured.
536 The configuration manager encountered more than one sequence rule specified in the same phase
537 The configuration manager encountered an error when invoking the program in the sequence rule.
538 The configuration manager is going to invoke a configuration method.
539 The configuration method has terminated, and control has returned to the configuration manager.
541 A DLT tape device is being configured.
549 Console could not be configured for the Copy a System Dump Menu.
551 IPL vary-on is running.
552 IPL vary-on failed.
553 IPL phase 1 is complete.
554 The boot device could not be opened or read, or unable to define NFS swap device during network boot.
555 An ODM error occurred when trying to vary-on the rootvg, or unable to create an NFS swap device during network boot.
556 Logical Volume Manager encountered error during IPL vary-on.
557 The root filesystem does not mount.
558 There is not enough memory to continue the system IPL.
559 Less than 2 M bytes of good memory are available to load the AIX kernel.
569 FCS SCSI protocol device is being configured (32 bits).
570 Virtual SCSI devices being configured.
571 HIPPI common function device driver being configured.
572 HIPPI IPI-3 master transport driver being configured.
573 HIPPI IPI-3 slave transport driver being configured.
574 HIPPI IPI-3 transport services user interface device driver being configured.
575 A 9570 disk-array driver being configured.
576 Generic async device driver being configured.
577 Generic SCSI device driver being configured.
578 Generic commo device driver being configured.
579 Device driver being configured for a generic device.
580 HIPPI TCPIP network interface driver being configured.
581 Configuring TCP/IP.
582 Configuring Token-Ring data link control.
583 Configuring an Ethernet data link control.
584 Configuring an IEEE Ethernet data link control.
585 Configuring an SDLC MPQP data link control.
586 Configuring a QLLC X.25 data link control.
587 Configuring a NETBIOS.
588 Configuring a Bisync Read-Write (BSCRW).
589 SCSI target mode device being configured.
590 Diskless remote paging device being configured.
591 Configuring an LVM device driver.
592 Configuring an HFT device driver.
593 Configuring SNA device drivers.
594 Asynchronous I/O being defined or configured.
595 X.31 pseudo-device being configured.
596 SNA DLC/LAPE pseudo-device being configured.
597 OCS software being configured.
598 OCS hosts being configured during system reboot.
599 Configuring FDDI data link control.
59B FCS SCSI protocol device being configured (64 bits).
5C0 Streams-based hardware drive being configured.
5C1 Streams-based X.25 protocol being configured.
5C2 Streams-based X.25 COMIO emulator driver being configured
5C3 Streams-based X.25 TCP/IP interface driver being configured.
5C4 FCS adapter device driver being configured.
5C5 SCB network device driver for FCS being configured.
5C6 AIX SNA channel being configured.
600 Starting network boot portion of /sbin/rc.boot.
602 Configuring network parent devices.
603 /usr/lib/methods/defsys, /usr/lib/methods/cfgsys, or /usr/lib/methods/cfgbus failed.
604 Configuring physical network boot device.
605 Configuration of physical network boot device failed.
606 Running /usr/sbin/ifconfig on logical network boot device.
607 /usr/sbin/ifconfig failed.
608 Attempting to retrieve the client.info file with tftp.Note that a flashing 608 indicates multiple attempt(s)
to etriever the client_info file are occurring.
609 The client.info file does not exist or it is zero length.
60B 18.2GB 68-pin LVD SCSI Disk Drive being configured.
610 Attempting remote mount of NFS file system.
611 Remote mount of the NFS file system failed.
612 Accessing remote files; unconfiguring network boot device.
614 Configuring local paging devices.
615 Configuration of a local paging device failed.
616 Converting from diskless to dataless configuration.
617 Diskless to dataless configuration failed.
618 Configuring remote (NFS) paging devices.
619 Configuration of a remote (NFS) paging device failed.
61B 36.4GB 80-pin LVD SCSI Disk Drive being configured.
61D 36.4GB 80-pin LVD SCSI Disk Drive being configured.
61E 18.2GB 68-pin LVD SCSI Disk Drive being configured.
620 Updating special device files and ODM in permanent filesystem with data from boot RAM filesystem.
621 9.1 GB LVD 80-pin SCSI Drive being configured.
622 Boot process configuring for operating system installation.
62D 9.1GB 68-pin LVD SCSI Disk Drive being configured.
62E 9.1GB 68-pin LVD SCSI Disk Drive being configured.
636 TURBROWAYS 622 Mbps PCI MMF ATM Adapter.
637 Dual Channel PCI-2 Ultra2 SCSI Adapter being configured.
638 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
639 9.1GB 10K RPM Ultra SCSI Disk Drive (68-pin).
63A See 62D.
63B 9.1GB 80-pin LVD SCSI Disk Drive being configured.
63C See 60B.
63D 18.2GB 80-pin LVD SCSI Disk Drive being configured.
63E 36.4GB 68-pin LVD SCSI Disk Drive being configured.
63F See 61B.
640 9.1GB 10K RPM Ultra SCSI Disk Drive (80-pin).
646 High-Speed Token-Ring PCI Adapter being configured.
64A See 62E.
64B 9.1GB 80-pin LVD SCSI Disk Drive being configured.
64C See 61E.
64D 18.2 GB LVD 80-pin Drive/Carrier being configured.
64E 36.4GB 68-pin LVD SCSI Disk Drive being configured.
64F See 61D.
650 IBM SCSD disk drive being configured.
653 18.2GB Ultra-SCSI 16-bit Disk Drive being configured.
655 GXT130P Graphics adapter being configured.
657 GXT2000P graphics adapter being configured.
658 PCI Fibre Channel Disk Subsystem Controller being identified or configured.
659 2102 Fibre Channel Disk Subsystem Controller Drawer being identified or configured.
660 2102 Fibre Channel Disk Array being identified or configured.
662 Ultra2 Integrated SCSI controller.
663 The ARTIC960RxD Digital Trunk Quad PCI Adapter or the ARTIC960RxF Digital Trunk Resource Adapter being configured.
664 32x (MAX) SCSI-2 CD-ROM drive being configured.
667 PCI 3-Channel Ultra2 SCSI RAID Adapter being configured.
669 PCI Gigabit Ethernet Adapter being configured.
66C 10/100/1000 Base-T EthernetPCI Adapter.
66D PCI 4-Channel Ultra-3 SCSI RAID Adapter.
66E 4.7 GB DVD-RAM drive.
674 ESCON(R) Channel PCI Adapter being configured.
677 PCI 32-bit Fibre Channel Arbitrated Loop Adapter being configured.
67B PCI Cryptographic Coprocessor being configured.
682 20x (MAX) SCSI-2 CD-ROM Drive being configured.
689 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
68C 20 GB 4-mm Tape Drive being configured.
68E POWER GXT6000P PCI Graphics Adapter.
690 9.1GB Ultra SCSI Single Ended Disk Drive being configured.
69b 64-bit/66MHz PCI ATM 155 MMF PCI adapter being configured.
69d 64-bit/66MHz PCI ATM 155 UTP PCI adapter being configured.
6CC SSA disk drive being configured.
700 A 1.1 GB 8-bit SCSI disk drive being identified or configured.
701 A 1.1 GB 16-bit SCSI disk drive being identified or configured.
702 A 1.1 GB 16-bit differential SCSI disk drive being identified or configured.
703 A 2.2 GB 8-bit SCSI disk drive being identified or configured.
704 A 2.2 GB 16-bit SCSI disk drive being identified or configured.
705 The configuration method for the 2.2 GB 16-bit differential SCSI disk drive is being run.
If an irrecoverable error occurs, the system halts.
706 A 4.5 GB 16-bit SCSI disk drive being identified or configured.
707 A 4.5 GB 16-bit differential SCSI disk drive being identified or configured.
708 A L2 cache being identified or configured.
710 POWER GXT150M graphics adapter being identified or configured.
711 Unknown adapter being identified or configured.
712 Graphics slot bus configuration is executing.
713 The IBM ARTIC960 device being configured.
714 A video capture adapter being configured.
715 The Ultramedia Services audio adapter being configured. (this number displays briefly on the panel).
717 TP Ethernet Adapter being configured.
718 GXT500 Graphics Adapter being configured.
720 Unknown read/write optical drive type being configured.
721 Unknown disk or SCSI device being identified or configured.
722 Unknown disk being identified or configured.
723 Unknown CD-ROM being identified or configured.
724 Unknown tape drive being identified or configured.
725 Unknown display adapter being identified or configured.
726 Unknown input device being identified or configured.
727 Unknown async device being identified or configured.
728 Parallel printer being identified or configured.
729 Unknown parallel device being identified or configured.
730 Unknown diskette drive being identified or configured.
731 PTY being identified or configured.
732 Unknown SCSI initiator type being configured.
733 7GB 8 mm tape drive being configured.
734 4x SCSI-2 640 MB CD-ROM Drive being configured.
736 Quiet Touch keyboard and speaker cable being configured.
741 1080 MB SCSI Disk Drive being configured.
745 16GB 4 mm Tape Auto Loader being configured.
746 SCSI-2 Fast/Wide PCI Adapter being configured.
747 SCSI-2 Differential Fast/Wide PCI Adapter being configured.
749 7331 Model 205 Tape Library being configured.
751 SCSI 32-bit SE F/W RAID Adapter being configured.
754 1.1GB 16-bit SCSI disk drive being configured.
755 2.2GB 16-bit SCSI disk drive being configured.
756 4.5GB 16-bit SCSI disk drive being configured.
757 External 13GB 1.5M/s 1/4 inch tape being configured.
763 SP Switch MX Adapter being configured.
764 SP System Attachment Adapter being configured.
772 4.5GB SCSI F/W Disk Drive being configured.
773 9.1GB SCSI F/W Disk Drive being configured.
774 9.1GB External SCSI Disk Drive being configured.
776 PCI Token-Ring Adapter being identified or configured.
777 10/100 Ethernet Tx PCI Adapter being identified or configured.
778 POWER GXT3000P 3D PCI Graphics adapter being configured.
77B 4-Port 10/100 Ethernet Tx PCI Adapter being identified or configured.
77c A 1.0 GB 16-bit SCSI disk drive being identified or configured.
783 4 mm DDS-2 Tape Autoloader being configured.
789 2.6 GB External Optical Drive being configured.
78B POWER GXT4000P PCI Graphics Adapter.
78C PCI bus configuration executing.
78D GXT300P 2D Graphics adapter being configured.
790 Multi-bus Integrated Ethernet Adapter being identified or configured.
797 TURBOWAYS(R) 155 UTP/STP ATM Adapter being identified or configured.
798 Video streamer adapter being identified or configured.
799 2-Port Multiprotocol PCI adapter being identified or configured.
79c ISA bus configuration executing.
7C0 CPU/System Interface being configured.
7C1 Business Audio Subsystem being identified or configured.
7cc PCMCIA bus configuration executing.
800 TURBOWAYS 155 MMF ATM Adapter being identified or configured.
803 7336 Tape Library robotics being configured.
804 8x Speed SCSI-2 CD-ROM Drive being configured.
806 POWER GXT800 PCI Graphics adapter being configured.
807 SCSI Device Enclosure being configured.
80c SSA 4-Port Adapter being identified or configured.
811 Processor complex being identified or configured.
812 Memory being identified or configured.
813 Battery for time-of-day, NVRAM, and so on being identified or configured
or system I/O control logic being identified or configured.
814 NVRAM being identified or configured.
815 Floating-point processor test.
816 Operator panel logic being identified or configured.
817 Time-of-day logic being identified or configured.
819 Graphics input device adapter being identified or configured.
821 Standard keyboard adapter being identified or configured.
823 Standard mouse adapter being identified or configured.
824 Standard tablet adapter being identified or configured.
825 Standard speaker adapter being identified or configured.
826 Serial Port 1 adapter being identified or configured.
827 Parallel port adapter being identified or configured.
828 Standard diskette adapter being identified or configured.
831 3151 adapter being identified or configured, or Serial Port 2 being identified or configured.
834 64-port async controller being identified or configured.
835 16-port async concentrator being identified or configured.
836 128-port async controller being identified or configured.
837 16-port remote async node being identified or configured.
838 Network Terminal Accelerator Adapter being identified or configured.
839 7318 Serial Communications Server being configured.
840 PCI Single-Ended Ultra SCSI Adapter being configured.
841 8-port async adapter (EIA-232) being identified or configured.
842 8-port async adapter (EIA-422A) being identified or configured.
843 8-port async adapter (MIL-STD 188) being identified or configured.
844 7135 RAIDiant Array disk drive subsystem controller being identified or configured.
845 7135 RAIDiant Array disk drive subsystem drawer being identified or configured.
846 RAIDiant Array SCSI 1.3GB Disk Drive being configured.
847 16-port serial adapter (EIA-232) being identified or configured.
848 16-port serial adapter (EIA-422) being identified or configured.
849 X.25 Interface Coprocessor/2 adapter being identified or configured.
850 Token-Ring network adapter being identified or configured.
851 T1/J1 Portmaster(R) adapter being identified or configured.
852 Ethernet adapter being identified or configured.
854 3270 Host Connection Program/6000 connection being identified or configured.
855 Portmaster Adapter/A being identified or configured.
857 FSLA adapter being identified or configured.
858 5085/5086/5088 adapter being identified or configured.
859 FDDI adapter being identified or configured.
85c Token-Ring High-Performance LAN adapter being identified or configured.
861 Optical adapter being identified or configured.
862 Block Multiplexer Channel Adapter being identified or configured.
865 ESCON Channel Adapter or emulator being identified or configured.
866 SCSI adapter being identified or configured.
867 Async expansion adapter being identified or configured.
868 SCSI adapter being identified or configured.
869 SCSI adapter being identified or configured.
870 Serial disk drive adapter being identified or configured.
871 Graphics subsystem adapter being identified or configured.
872 Grayscale graphics adapter being identified or configured.
874 Color graphics adapter being identified or configured.
875 Vendor generic communication adapter being configured.
876 8-bit color graphics processor being identified or configured.
877 POWER Gt3(TM)/POWER Gt4(TM) being identified or configured.
878 POWER Gt4 graphics processor card being configured.
879 24-bit color graphics card, MEV2 being configured.
880 POWER Gt1(TM) adapter being identified or configured.
887 Integrated Ethernet adapter being identified or configured.
889 SCSI adapter being identified or configured.
890 SCSI-2 Differential Fast/Wide and Single-Ended Fast/Wide Adapter/A being configured.
891 Vendor SCSI adapter being identified or configured.
892 Vendor display adapter being identified or configured.
893 Vendor LAN adapter being identified or configured.
894 Vendor async/communications adapter being identified or configured.
895 Vendor IEEE 488 adapter being identified or configured.
896 Vendor VME bus adapter being identified or configured.
897 S/370(TM) Channel Emulator adapter being identified or configured.
898 POWER Gt1x(TM) graphics adapter being identified or configured.
899 3490 attached tape drive being identified or configured.
89c A multimedia SCSI CD-ROM being identified or configured.
900 GXT110P Graphics Adapter being identified or configured.
901 Vendor SCSI device being identified or configured.
902 Vendor display device being identified or configured.
903 Vendor async device being identified or configured.
904 Vendor parallel device being identified or configured.
905 Vendor other device being identified or configured.
908 POWER GXT1000 Graphics subsystem being identified or configured.
910 1/4GB Fiber Channel/266 Standard Adapter being identified or configured.
911 Fiber Channel/1063 Adapter Short Wave being configured.
912 2.0GB SCSI-2 differential disk drive being identified or configured.
913 1.0GB differential disk drive being identified or configured.
914 5GB 8 mm differential tape drive being identified or configured.
915 4GB 4 mm tape drive being identified or configured.
916 Non-SCSI vendor tape adapter being identified or configured.
917 A 2.0 GB 16-bit differential SCSI disk drive being identified or configured.
918 A 2 GB 16-bit single-ended SCSI disk drive being identified or configured.
920 Bridge Box being identified or configured.
921 101 keyboard being identified or configured.
922 102 keyboard being identified or configured.
923 Kanji keyboard being identified or configured.
924 Two-button mouse being identified or configured.
925 Three-button mouse being identified or configured.
926 5083 tablet being identified or configured.
927 5083 tablet being identified or configured.
928 Standard speaker being identified or configured.
929 Dials being identified or configured.
930 Lighted program function keys (LPFK) being identified or configured.
931 IP router being identified or configured.
933 Async planar being identified or configured.
934 Async expansion drawer being identified or configured.
935 3.5-inch diskette drive being identified or configured.
936 5.25-inch diskette drive being identified or configured.
937 An HIPPI adapter being configured.
938 Serial HIPPI PCI adapter being configured.
942 POWER GXT 100 graphics adapter being identified or configured.
943 A 3480 or 3490 control unit attached to a System/370 Channel Emulator/A adapter are being identified or configured.
944 100MB ATM adapter being identified or configured.
945 1.0GB SCSI differential disk drive being identified or configured.
946 Serial port 3 adapter being identified or configured.
947 A 730MB SCSI disk drive being configured.
948 Portable disk drive being identified or configured.
949 Unknown direct bus-attach device being identified or configured.
950 Missing SCSI device being identified or configured.
951 670MB SCSI disk drive being identified or configured.
952 355MB SCSI disk drive being identified or configured.
953 320MB SCSI disk drive being identified or configured.
954 400MB SCSI disk drive being identified or configured.
955 857MB SCSI disk drive being identified or configured.
956 670MB SCSI disk drive electronics card being identified or configured.
957 120 MB DBA disk drive being identified or configured.
958 160 MB DBA disk drive being identified or configured.
959 160 MB SCSI disk drive being identified or configured.
960 1.37GB SCSI disk drive being identified or configured.
964 Internal 20 GB 8 mm tape drive identified or configured.
968 1.0 GB SCSI disk drive being identified or configured.
970 Half-inch, 9-track tape drive being identified or configured.
971 150 MB 1/4-inch tape drive being identified or configured.
972 2.3 GB 8 mm SCSI tape drive being identified or configured.
973 Other SCSI tape drive being identified or configured.
974 CD-ROM drive being identified or configured.
975 An optical disk drive being identified or configured.
977 M-Audio Capture and Playback Adapter being identified or configured.
981 540MB SCSI-2 single-ended disk drive being identified or configured.
984 1GB 8-bit disk drive being identified or configured.
985 M-Video Capture Adapter being identified or configured.
986 2.4GB SCSI disk drive being identified or configured.
987 An Enhanced SCSI CD-ROM drive being identified or configured.
989 200MB SCSI disk drive being identified or configured.
990 2.0GB SCSI-2 single-ended disk drive being identified or configured.
991 525MB 1/4-inch cartridge tape drive being identified or configured.
994 5 GB 8 mm tape drive being identified or configured.
995 1.2GB 1/4 inch cartridge tape drive being identified or configured.
996 A single-port, multiprotocol communications adapter being identified or configured.
997 FDDI adapter being identified or configured.
998 2.0 GB 4 mm tape drive being identified or configured.
999 7137 or 3514 Disk Array Subsystem being configured.
D46 Token-Ring cable
D81 T2 Ethernet Adapter being configured.
2530 10/100 Mbps Ethernet PCI Adapter II being configured.
2E7 Configuration method unable to determine if the SCSI adapter type is SE or DE type.
440 9.1GB Ultra SCSI Disk Drive being identified or configured.
441 18.2GB Ultra SCSI Disk Drive being identified or configured.
444 2-Port Multiprotocol PCI Adapter (ASIC) being identified or configured.
447 PCI 64-bit Fibre Channel Arbitrated Loop Adapter being configured.
500 Querying Standard I/O slot.
501 Querying card in Slot 1.
502 Querying card in Slot 2.
503 Querying card in Slot 3.
504 Querying card in Slot 4.
505 Querying card in Slot 5.
506 Querying card in Slot 6.
507 Querying card in Slot 7.
508 Querying card in Slot 8.
510 Starting device configuration.
511 Device configuration completed.
512 Restoring device configuration files from media.
513 Restoring basic operating system installation files from media.
516 Contacting server during network boot.
517 Mounting client remote file system during network IPL.
518 Remote mount of the root (/) and /usr file systems failed during network boot.
520 Bus configuration running.
521 /etc/init invoked cfgmgr with invalid options;
/etc/inithas been corrupted or incorrectly modified (irrecoverable error).
522 The configuration manager has been invoked with conflicting options (irrecoverable error).
523 The configuration manager is unable to access the ODM database (irrecoverable error).
524 The configuration manager is unable to access the config.rules object in the ODM database
525 The configuration manager is unable to get data from a customized device object in the ODM database
526 The configuration manager is unable to get data from a customized device driver object in the ODM database
527 The configuration manager was invoked with the phase 1 flag; running phase 1 at this point is not permitted
528 The configuration manager cannot find sequence rule, or no program name was specified in the ODM database
529 The configuration manager is unable to update ODM data (irrecoverable error).
530 The program savebase returned an error.
531 The configuration manager is unable to access the PdAt object class (irrecoverable error).
532 There is not enough memory to continue (malloc failure); irrecoverable error.
533 The configuration manager could not find a configuration method for a device.
534 The configuration manager is unable to acquire database lock (irrecoverable error).
535 HIPPI diagnostics interface driver being configured.
536 The configuration manager encountered more than one sequence rule specified in the same phase
537 The configuration manager encountered an error when invoking the program in the sequence rule.
538 The configuration manager is going to invoke a configuration method.
539 The configuration method has terminated, and control has returned to the configuration manager.
541 A DLT tape device is being configured.
549 Console could not be configured for the Copy a System Dump Menu.
551 IPL vary-on is running.
552 IPL vary-on failed.
553 IPL phase 1 is complete.
554 The boot device could not be opened or read, or unable to define NFS swap device during network boot.
555 An ODM error occurred when trying to vary-on the rootvg, or unable to create an NFS swap device during network boot.
556 Logical Volume Manager encountered error during IPL vary-on.
557 The root filesystem does not mount.
558 There is not enough memory to continue the system IPL.
559 Less than 2 M bytes of good memory are available to load the AIX kernel.
569 FCS SCSI protocol device is being configured (32 bits).
570 Virtual SCSI devices being configured.
571 HIPPI common function device driver being configured.
572 HIPPI IPI-3 master transport driver being configured.
573 HIPPI IPI-3 slave transport driver being configured.
574 HIPPI IPI-3 transport services user interface device driver being configured.
575 A 9570 disk-array driver being configured.
576 Generic async device driver being configured.
577 Generic SCSI device driver being configured.
578 Generic commo device driver being configured.
579 Device driver being configured for a generic device.
580 HIPPI TCPIP network interface driver being configured.
581 Configuring TCP/IP.
582 Configuring Token-Ring data link control.
583 Configuring an Ethernet data link control.
584 Configuring an IEEE Ethernet data link control.
585 Configuring an SDLC MPQP data link control.
586 Configuring a QLLC X.25 data link control.
587 Configuring a NETBIOS.
588 Configuring a Bisync Read-Write (BSCRW).
589 SCSI target mode device being configured.
590 Diskless remote paging device being configured.
591 Configuring an LVM device driver.
592 Configuring an HFT device driver.
593 Configuring SNA device drivers.
594 Asynchronous I/O being defined or configured.
595 X.31 pseudo-device being configured.
596 SNA DLC/LAPE pseudo-device being configured.
597 OCS software being configured.
598 OCS hosts being configured during system reboot.
599 Configuring FDDI data link control.
59B FCS SCSI protocol device being configured (64 bits).
5C0 Streams-based hardware drive being configured.
5C1 Streams-based X.25 protocol being configured.
5C2 Streams-based X.25 COMIO emulator driver being configured
5C3 Streams-based X.25 TCP/IP interface driver being configured.
5C4 FCS adapter device driver being configured.
5C5 SCB network device driver for FCS being configured.
5C6 AIX SNA channel being configured.
600 Starting network boot portion of /sbin/rc.boot.
602 Configuring network parent devices.
603 /usr/lib/methods/defsys, /usr/lib/methods/cfgsys, or /usr/lib/methods/cfgbus failed.
604 Configuring physical network boot device.
605 Configuration of physical network boot device failed.
606 Running /usr/sbin/ifconfig on logical network boot device.
607 /usr/sbin/ifconfig failed.
608 Attempting to retrieve the client.info file with tftp.Note that a flashing 608 indicates multiple attempt(s)
to etriever the client_info file are occurring.
609 The client.info file does not exist or it is zero length.
60B 18.2GB 68-pin LVD SCSI Disk Drive being configured.
610 Attempting remote mount of NFS file system.
611 Remote mount of the NFS file system failed.
612 Accessing remote files; unconfiguring network boot device.
614 Configuring local paging devices.
615 Configuration of a local paging device failed.
616 Converting from diskless to dataless configuration.
617 Diskless to dataless configuration failed.
618 Configuring remote (NFS) paging devices.
619 Configuration of a remote (NFS) paging device failed.
61B 36.4GB 80-pin LVD SCSI Disk Drive being configured.
61D 36.4GB 80-pin LVD SCSI Disk Drive being configured.
61E 18.2GB 68-pin LVD SCSI Disk Drive being configured.
620 Updating special device files and ODM in permanent filesystem with data from boot RAM filesystem.
621 9.1 GB LVD 80-pin SCSI Drive being configured.
622 Boot process configuring for operating system installation.
62D 9.1GB 68-pin LVD SCSI Disk Drive being configured.
62E 9.1GB 68-pin LVD SCSI Disk Drive being configured.
636 TURBROWAYS 622 Mbps PCI MMF ATM Adapter.
637 Dual Channel PCI-2 Ultra2 SCSI Adapter being configured.
638 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
639 9.1GB 10K RPM Ultra SCSI Disk Drive (68-pin).
63A See 62D.
63B 9.1GB 80-pin LVD SCSI Disk Drive being configured.
63C See 60B.
63D 18.2GB 80-pin LVD SCSI Disk Drive being configured.
63E 36.4GB 68-pin LVD SCSI Disk Drive being configured.
63F See 61B.
640 9.1GB 10K RPM Ultra SCSI Disk Drive (80-pin).
646 High-Speed Token-Ring PCI Adapter being configured.
64A See 62E.
64B 9.1GB 80-pin LVD SCSI Disk Drive being configured.
64C See 61E.
64D 18.2 GB LVD 80-pin Drive/Carrier being configured.
64E 36.4GB 68-pin LVD SCSI Disk Drive being configured.
64F See 61D.
650 IBM SCSD disk drive being configured.
653 18.2GB Ultra-SCSI 16-bit Disk Drive being configured.
655 GXT130P Graphics adapter being configured.
657 GXT2000P graphics adapter being configured.
658 PCI Fibre Channel Disk Subsystem Controller being identified or configured.
659 2102 Fibre Channel Disk Subsystem Controller Drawer being identified or configured.
660 2102 Fibre Channel Disk Array being identified or configured.
662 Ultra2 Integrated SCSI controller.
663 The ARTIC960RxD Digital Trunk Quad PCI Adapter or the ARTIC960RxF Digital Trunk Resource Adapter being configured.
664 32x (MAX) SCSI-2 CD-ROM drive being configured.
667 PCI 3-Channel Ultra2 SCSI RAID Adapter being configured.
669 PCI Gigabit Ethernet Adapter being configured.
66C 10/100/1000 Base-T EthernetPCI Adapter.
66D PCI 4-Channel Ultra-3 SCSI RAID Adapter.
66E 4.7 GB DVD-RAM drive.
674 ESCON(R) Channel PCI Adapter being configured.
677 PCI 32-bit Fibre Channel Arbitrated Loop Adapter being configured.
67B PCI Cryptographic Coprocessor being configured.
682 20x (MAX) SCSI-2 CD-ROM Drive being configured.
689 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
68C 20 GB 4-mm Tape Drive being configured.
68E POWER GXT6000P PCI Graphics Adapter.
690 9.1GB Ultra SCSI Single Ended Disk Drive being configured.
69b 64-bit/66MHz PCI ATM 155 MMF PCI adapter being configured.
69d 64-bit/66MHz PCI ATM 155 UTP PCI adapter being configured.
6CC SSA disk drive being configured.
700 A 1.1 GB 8-bit SCSI disk drive being identified or configured.
701 A 1.1 GB 16-bit SCSI disk drive being identified or configured.
702 A 1.1 GB 16-bit differential SCSI disk drive being identified or configured.
703 A 2.2 GB 8-bit SCSI disk drive being identified or configured.
704 A 2.2 GB 16-bit SCSI disk drive being identified or configured.
705 The configuration method for the 2.2 GB 16-bit differential SCSI disk drive is being run.
If an irrecoverable error occurs, the system halts.
706 A 4.5 GB 16-bit SCSI disk drive being identified or configured.
707 A 4.5 GB 16-bit differential SCSI disk drive being identified or configured.
708 A L2 cache being identified or configured.
710 POWER GXT150M graphics adapter being identified or configured.
711 Unknown adapter being identified or configured.
712 Graphics slot bus configuration is executing.
713 The IBM ARTIC960 device being configured.
714 A video capture adapter being configured.
715 The Ultramedia Services audio adapter being configured. (this number displays briefly on the panel).
717 TP Ethernet Adapter being configured.
718 GXT500 Graphics Adapter being configured.
720 Unknown read/write optical drive type being configured.
721 Unknown disk or SCSI device being identified or configured.
722 Unknown disk being identified or configured.
723 Unknown CD-ROM being identified or configured.
724 Unknown tape drive being identified or configured.
725 Unknown display adapter being identified or configured.
726 Unknown input device being identified or configured.
727 Unknown async device being identified or configured.
728 Parallel printer being identified or configured.
729 Unknown parallel device being identified or configured.
730 Unknown diskette drive being identified or configured.
731 PTY being identified or configured.
732 Unknown SCSI initiator type being configured.
733 7GB 8 mm tape drive being configured.
734 4x SCSI-2 640 MB CD-ROM Drive being configured.
736 Quiet Touch keyboard and speaker cable being configured.
741 1080 MB SCSI Disk Drive being configured.
745 16GB 4 mm Tape Auto Loader being configured.
746 SCSI-2 Fast/Wide PCI Adapter being configured.
747 SCSI-2 Differential Fast/Wide PCI Adapter being configured.
749 7331 Model 205 Tape Library being configured.
751 SCSI 32-bit SE F/W RAID Adapter being configured.
754 1.1GB 16-bit SCSI disk drive being configured.
755 2.2GB 16-bit SCSI disk drive being configured.
756 4.5GB 16-bit SCSI disk drive being configured.
757 External 13GB 1.5M/s 1/4 inch tape being configured.
763 SP Switch MX Adapter being configured.
764 SP System Attachment Adapter being configured.
772 4.5GB SCSI F/W Disk Drive being configured.
773 9.1GB SCSI F/W Disk Drive being configured.
774 9.1GB External SCSI Disk Drive being configured.
776 PCI Token-Ring Adapter being identified or configured.
777 10/100 Ethernet Tx PCI Adapter being identified or configured.
778 POWER GXT3000P 3D PCI Graphics adapter being configured.
77B 4-Port 10/100 Ethernet Tx PCI Adapter being identified or configured.
77c A 1.0 GB 16-bit SCSI disk drive being identified or configured.
783 4 mm DDS-2 Tape Autoloader being configured.
789 2.6 GB External Optical Drive being configured.
78B POWER GXT4000P PCI Graphics Adapter.
78C PCI bus configuration executing.
78D GXT300P 2D Graphics adapter being configured.
790 Multi-bus Integrated Ethernet Adapter being identified or configured.
797 TURBOWAYS(R) 155 UTP/STP ATM Adapter being identified or configured.
798 Video streamer adapter being identified or configured.
799 2-Port Multiprotocol PCI adapter being identified or configured.
79c ISA bus configuration executing.
7C0 CPU/System Interface being configured.
7C1 Business Audio Subsystem being identified or configured.
7cc PCMCIA bus configuration executing.
800 TURBOWAYS 155 MMF ATM Adapter being identified or configured.
803 7336 Tape Library robotics being configured.
804 8x Speed SCSI-2 CD-ROM Drive being configured.
806 POWER GXT800 PCI Graphics adapter being configured.
807 SCSI Device Enclosure being configured.
80c SSA 4-Port Adapter being identified or configured.
811 Processor complex being identified or configured.
812 Memory being identified or configured.
813 Battery for time-of-day, NVRAM, and so on being identified or configured
or system I/O control logic being identified or configured.
814 NVRAM being identified or configured.
815 Floating-point processor test.
816 Operator panel logic being identified or configured.
817 Time-of-day logic being identified or configured.
819 Graphics input device adapter being identified or configured.
821 Standard keyboard adapter being identified or configured.
823 Standard mouse adapter being identified or configured.
824 Standard tablet adapter being identified or configured.
825 Standard speaker adapter being identified or configured.
826 Serial Port 1 adapter being identified or configured.
827 Parallel port adapter being identified or configured.
828 Standard diskette adapter being identified or configured.
831 3151 adapter being identified or configured, or Serial Port 2 being identified or configured.
834 64-port async controller being identified or configured.
835 16-port async concentrator being identified or configured.
836 128-port async controller being identified or configured.
837 16-port remote async node being identified or configured.
838 Network Terminal Accelerator Adapter being identified or configured.
839 7318 Serial Communications Server being configured.
840 PCI Single-Ended Ultra SCSI Adapter being configured.
841 8-port async adapter (EIA-232) being identified or configured.
842 8-port async adapter (EIA-422A) being identified or configured.
843 8-port async adapter (MIL-STD 188) being identified or configured.
844 7135 RAIDiant Array disk drive subsystem controller being identified or configured.
845 7135 RAIDiant Array disk drive subsystem drawer being identified or configured.
846 RAIDiant Array SCSI 1.3GB Disk Drive being configured.
847 16-port serial adapter (EIA-232) being identified or configured.
848 16-port serial adapter (EIA-422) being identified or configured.
849 X.25 Interface Coprocessor/2 adapter being identified or configured.
850 Token-Ring network adapter being identified or configured.
851 T1/J1 Portmaster(R) adapter being identified or configured.
852 Ethernet adapter being identified or configured.
854 3270 Host Connection Program/6000 connection being identified or configured.
855 Portmaster Adapter/A being identified or configured.
857 FSLA adapter being identified or configured.
858 5085/5086/5088 adapter being identified or configured.
859 FDDI adapter being identified or configured.
85c Token-Ring High-Performance LAN adapter being identified or configured.
861 Optical adapter being identified or configured.
862 Block Multiplexer Channel Adapter being identified or configured.
865 ESCON Channel Adapter or emulator being identified or configured.
866 SCSI adapter being identified or configured.
867 Async expansion adapter being identified or configured.
868 SCSI adapter being identified or configured.
869 SCSI adapter being identified or configured.
870 Serial disk drive adapter being identified or configured.
871 Graphics subsystem adapter being identified or configured.
872 Grayscale graphics adapter being identified or configured.
874 Color graphics adapter being identified or configured.
875 Vendor generic communication adapter being configured.
876 8-bit color graphics processor being identified or configured.
877 POWER Gt3(TM)/POWER Gt4(TM) being identified or configured.
878 POWER Gt4 graphics processor card being configured.
879 24-bit color graphics card, MEV2 being configured.
880 POWER Gt1(TM) adapter being identified or configured.
887 Integrated Ethernet adapter being identified or configured.
889 SCSI adapter being identified or configured.
890 SCSI-2 Differential Fast/Wide and Single-Ended Fast/Wide Adapter/A being configured.
891 Vendor SCSI adapter being identified or configured.
892 Vendor display adapter being identified or configured.
893 Vendor LAN adapter being identified or configured.
894 Vendor async/communications adapter being identified or configured.
895 Vendor IEEE 488 adapter being identified or configured.
896 Vendor VME bus adapter being identified or configured.
897 S/370(TM) Channel Emulator adapter being identified or configured.
898 POWER Gt1x(TM) graphics adapter being identified or configured.
899 3490 attached tape drive being identified or configured.
89c A multimedia SCSI CD-ROM being identified or configured.
900 GXT110P Graphics Adapter being identified or configured.
901 Vendor SCSI device being identified or configured.
902 Vendor display device being identified or configured.
903 Vendor async device being identified or configured.
904 Vendor parallel device being identified or configured.
905 Vendor other device being identified or configured.
908 POWER GXT1000 Graphics subsystem being identified or configured.
910 1/4GB Fiber Channel/266 Standard Adapter being identified or configured.
911 Fiber Channel/1063 Adapter Short Wave being configured.
912 2.0GB SCSI-2 differential disk drive being identified or configured.
913 1.0GB differential disk drive being identified or configured.
914 5GB 8 mm differential tape drive being identified or configured.
915 4GB 4 mm tape drive being identified or configured.
916 Non-SCSI vendor tape adapter being identified or configured.
917 A 2.0 GB 16-bit differential SCSI disk drive being identified or configured.
918 A 2 GB 16-bit single-ended SCSI disk drive being identified or configured.
920 Bridge Box being identified or configured.
921 101 keyboard being identified or configured.
922 102 keyboard being identified or configured.
923 Kanji keyboard being identified or configured.
924 Two-button mouse being identified or configured.
925 Three-button mouse being identified or configured.
926 5083 tablet being identified or configured.
927 5083 tablet being identified or configured.
928 Standard speaker being identified or configured.
929 Dials being identified or configured.
930 Lighted program function keys (LPFK) being identified or configured.
931 IP router being identified or configured.
933 Async planar being identified or configured.
934 Async expansion drawer being identified or configured.
935 3.5-inch diskette drive being identified or configured.
936 5.25-inch diskette drive being identified or configured.
937 An HIPPI adapter being configured.
938 Serial HIPPI PCI adapter being configured.
942 POWER GXT 100 graphics adapter being identified or configured.
943 A 3480 or 3490 control unit attached to a System/370 Channel Emulator/A adapter are being identified or configured.
944 100MB ATM adapter being identified or configured.
945 1.0GB SCSI differential disk drive being identified or configured.
946 Serial port 3 adapter being identified or configured.
947 A 730MB SCSI disk drive being configured.
948 Portable disk drive being identified or configured.
949 Unknown direct bus-attach device being identified or configured.
950 Missing SCSI device being identified or configured.
951 670MB SCSI disk drive being identified or configured.
952 355MB SCSI disk drive being identified or configured.
953 320MB SCSI disk drive being identified or configured.
954 400MB SCSI disk drive being identified or configured.
955 857MB SCSI disk drive being identified or configured.
956 670MB SCSI disk drive electronics card being identified or configured.
957 120 MB DBA disk drive being identified or configured.
958 160 MB DBA disk drive being identified or configured.
959 160 MB SCSI disk drive being identified or configured.
960 1.37GB SCSI disk drive being identified or configured.
964 Internal 20 GB 8 mm tape drive identified or configured.
968 1.0 GB SCSI disk drive being identified or configured.
970 Half-inch, 9-track tape drive being identified or configured.
971 150 MB 1/4-inch tape drive being identified or configured.
972 2.3 GB 8 mm SCSI tape drive being identified or configured.
973 Other SCSI tape drive being identified or configured.
974 CD-ROM drive being identified or configured.
975 An optical disk drive being identified or configured.
977 M-Audio Capture and Playback Adapter being identified or configured.
981 540MB SCSI-2 single-ended disk drive being identified or configured.
984 1GB 8-bit disk drive being identified or configured.
985 M-Video Capture Adapter being identified or configured.
986 2.4GB SCSI disk drive being identified or configured.
987 An Enhanced SCSI CD-ROM drive being identified or configured.
989 200MB SCSI disk drive being identified or configured.
990 2.0GB SCSI-2 single-ended disk drive being identified or configured.
991 525MB 1/4-inch cartridge tape drive being identified or configured.
994 5 GB 8 mm tape drive being identified or configured.
995 1.2GB 1/4 inch cartridge tape drive being identified or configured.
996 A single-port, multiprotocol communications adapter being identified or configured.
997 FDDI adapter being identified or configured.
998 2.0 GB 4 mm tape drive being identified or configured.
999 7137 or 3514 Disk Array Subsystem being configured.
D46 Token-Ring cable
D81 T2 Ethernet Adapter being configured.
2530 10/100 Mbps Ethernet PCI Adapter II being configured.
Categories:
0 comments:
Post a Comment